当前位置:首页 >> 机械/仪表 >>

VW10540-1_En_062005_图文

Klass.-Nr. 01 15 5

June 2005

Manufacturer's Code
for Vehicle Parts Konzernnorm Descriptors: manufacturer, code, indentification, vehicle part

VW 105 40-1

Changes The following changes have been made as compared to Volkswagen standard VW 105 40-1, 199906:
─ ─ ─ ─ ─ ─ ─ ─

Section 1, paragraph 1: “..three or four-digit ..” changed to “…three-character…” Section 1, paragraph 1: Note on VW 105 14, VW 105 50, DIN 14 50 removed, “code” changed to “manufacturer's code” Section 1, paragraphs 4 and 5: Notes on contact partners and hyperlinks added. Section 1, paragraph 6: Note on “moldings” removed; alternative identifications supplemented Section 2: paragraph 1 removed Section 2, paragraph 2: Note added on missing identifications Section 2: Note added regarding VW 105 00 Section 3.1, Figure 1: Part number and date of manufacturing updated

Previous issues 1972-10; 1999-06 1 Scope

Vehicle parts or function groups that are purchased ready to be installed from vendors, are partially supplied by vendors, are taken from current production as spare or accessory parts, or are manufactured in-house as spare or accessory parts must be identified by a permanent and easily legible three-character manufacturer's code (alphabetic or alphanumeric) indicating the manufacturer. Identification by the manufacturer's code is required so that selective damage and quality analysis can be carried out if necessary and so that the manufacturer can always be identified in warranty and product liability cases. Manufacturer's codes have been established for all manufacturers and their individual production locations that supply vehicle parts to the Volkswagen Group and its brands, including its associated companies. The manufacturer's codes for Volkswagen AG and Audi AG are assigned on request. Suppliers can access information on contacts and procedures via the B2B supplier platform at www.vwgroupsupply.com. The manufacturer is notified of the assignment of the manufacturer code in writing. Manufacturer's codes for foreign affiliated companies are issued separately according to the issuing specifications defined in VW 105 40-3. The contacts for assigning manufacturer's codes in the Group companies abroad are likewise available via the B2B supplier platform at www.vwgroupsupply.com. A list of all manufacturer's codes (only for internal use) and contacts for awarding the manufacturer's code are likewise available in the NOLIS system at http://few.wob.vw.de/anbieter/eztn/herstellercode/code.xls.
Form FE 41 - 01.05

Page 1 of 4
Fachverantwortung/Responsibility EZTD Kühn Normung/Standards (EZTD, 1733) Kühn Tel: +49-5361-9-23370 Sobanski

Confidential. All rights reserved. No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the Volkswagen Group. Parties to a contract can only obtain this standard via the B2B supplier platform “www.vwgroupsupply.com”.

? VOLKSWAGEN AG

Norm vor Anwendung auf Aktualit?t prüfen / Check standard for current issue prior to usage.

Page 2 VW 105 40-1: 2005-06

The identification requirement for vehicle parts may be dropped in the following cases:
─ ─ ─

standard parts semifinished parts, parts for which identification is not possible because of space limitations and/or cannot be applied so that it is readable (see DIN 1450 for this term).

For parts which, due to their nature, cannot be identified with the manufacturer's code as per this standard, alternative forms of identification shall be agreed between the manufacturer and the center awarding the manufacturer's code, as shall the inclusion of same in the appropriate documents. Exception: For valve springs, color markings acc. to VW 105 40-7 are assigned to the manufacturer as an alternative manufacturer's code. 2 Requirements

Part identification shall be established immediately for newly developed items and first-order items. Missing identifications shall be applied immediately. Identification specification according to Figure 2 shall be ensured. Any codes that do not apply shall be deleted. The code characters shall be half the size of the trademark diameter “d1” or the trademark height “h” acc. to VW 105 14 if possible, but even when space is limited the size shall never be less than 2 mm. Assemblies (ASSY) that are sold as spare parts shall only be identified once by such a code, whereas any component part of an assembly that is listed individually as a spare part shall also be identified by a code. The identification on the part should if possible be located so that it is visible in as-installed position. When identifying parts that are in the visual range of the customer, agreement shall be reached with Design and the center assigning the manufacturer's code on the application position of the identification. Typeface according to DIN 1451, part 4 (medium-spaced lettering) applies to the identification. VW 105 00 contains further identification requirements.

Page 3 VW 105 40-1: 2005-06

3 3.1

Identification example (Figure 1) and drawing specifications (Figure 2) Identification example
Nenndurchmesser nach VW 105 14

(DE)
3) 2)

1) 2)

05

3D0
Figure 1 3.2 Drawing specifications for Figure 1 (text macro; VW 010 14, NO-E2): Kennzeichnung Identification Markenzeichen Trademark Herstellland Country of origin Hersteller-Code3) Mfr. Code Teil-Nr.; Schrift Pt.-No; Lettering Datumskennzeichnung Date of manufact. Werkstoff-Code Material code VW 105 00 VW 105 14 - C6 VW 105 50 – 3 VW 105 40 – 3 DIN 1451 – 3 VW 105 60 - A6 VDA 260 > PP + EPDM < Figure 2
1) 2) 3) In case of lack of space the 2-letter code acc. to VW 105 50 shall be used. Manufacturer's code has 3 characters Instead of the manufacturer's code acc. to VW 105 40, part 7 of the same standard shall be applied to valve springs.

Page 4 VW 105 40-1: 2005-06

4

Referenced standards Lettering, Legibility Typefaces; Lineal Linear-Antiqua; Stenciled Lettering for Engraving and Other Processes Technical Drawings; Drawing Frames and Text Macros Company Designation, Parts Identification; Guidelines for Use Logos; Identification of Vehicle Parts Manufacturer's Code fro Vehicle Parts; Issuing Ranges for International Plants Issuing Manufacturer's Codes Identification of Valve Springs

DIN 1450 DIN 1451-4 VW 010 14 VW 105 00 VW 105 14 VW 105 40-3 VW 105 40-7


相关文章:
VW10540-1_En_062005_图文.pdf
VW10540-1_En_062005 - Klass.-Nr. 01 15 5
VW10540 2005 CH_图文.pdf
VW10540 2005 CH_信息与通信_工程科技_专业资料。汽车电子 大众标准 制造商代码...VW 10550 4页 1下载券 VW10540-1_En_062005 4页 5下载券 VW 01155:200...
TL4225_EN_2006-05-01_图文.pdf
obtain this standard via the B2B supplier platform “www.vwgroupsupply.com...Determination according to DIN EN 10002-1. Page 6 TL 4225: 2006-05 ...
VW 10540-1.pdf
用户评价 这篇文档有word格式吗?VW 10540-1 2018-06-26 04:45:49 文档...大众汽车标准_VW_10540-... 暂无评价 8页 1下载券 VW10540 2005 CH 4页...
VW 01059T1_en_061993.pdf
VW 01059-5_En_052001 27页 2下载券 大众汽车标准_VW 011 55... 2页 免费 VW 10514_EN_大众标牌标... 6页 1下载券 VW 01043_EN_2006 4页 1...
VW 10540 汽车零部件供应商代码 2011 07 01.pdf
VW 10540-1: 1972-10, 1999-06, 2005-06, 2006-06 Changes The following changes have been made compared with VW 10540-1: 2006-06: Section 1: ...
DIN_EN_1092-1-2002_图文.pdf
1123 11.02 Page 2 DIN EN 1092-1 : 2002-06 DIN 2630: 1928-04, 1949...1949-05, 1954-12, 1962-08, 1966-08, 1975-03 1943-11, 1949-05, 1954...
VW80106_EN_2008-06-01.pdf
VW80106_EN_2008-06-01_专业资料。VW80106_EN_2008-06-01 ...参考标准目录 Page 1 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3 ...
更多相关标签: